MSG6130 Intelligent Differential Pressure Transmitter

Product Features	Adopting mature metal capacitive sensors with 0.1% high precision and 20:1 wide range, high stability and reliability, equipped with HART
	Communication function, with intrinsic safety, explosion-proof, high static pressure product series, equipped with special material isolation diaphragm, used for high
	Differential pressure measurement under temperature, high pressure, and strong corrosion conditions!

working principle	The medium pressure acts on the metal isolation corrugated membrane and is transmitted to the sensitive element beta chamber for measurement through the intermediate silicone oil
	The diaphragm senses differential pressure to form a capacitance change, and the differential pressure forms a linear state with the differential capacitance to detect electricity
	The differential pressure capacitance is amplified and converted into a standard current signal for output.

---

---

Technical Specifications	·Measurement range	Minimum measurement range 0~500Pa, maximum measurement range 0~4MPa
	·Accuracy	The comprehensive error (including linearity, repeatability, and hysteresis) is better than 0.1%
		<7KPa: 0.25% rated range 1:1~3:1 (0.25% standard range+0.03% TD)%
		Set the range to 3:1 to 10:1
		≥ 7kPa: 0.2% standard range 1:1~3:1 (0.2% standard range+0.03% TD)%
		Set the range to 3:1 to 10:1
	·Long term stability	Annually ≤ ± 0.15% Fs
	·Working temperature	Allowable medium temperature (-40~100) ℃, allowable storage temperature (-40~85) ℃
		Allowable ambient temperature (-20~60) ℃ (special requirement -40~85 ℃)
	·Temperature influence	-Within the temperature range of 20 ℃ to+60 ℃, the influence error (zero point, range) is ≤ 0.8%
		The influence error of the 7KPa range sensor is ≤ 1.2%
	·Temperature coefficient	-10 ℃~+60 ℃ (0.05% URL+0.065% set range)/20K
		-40 ℃~-10 ℃ 60 ℃~+85 ℃ (0.08% URL+0.1% set range)/20K
	·Long term stability and qualitative analysis	Better than 0.1% FS per year and better than 0.25% for five years
	·Sensors allow Working static pressure	Unidirectional and bidirectional maximum allowable static pressure PN13MPa
	·Static pressure influence	Under 100% condition, the impact is ≤ 0.25%
	·Damping	0-40 seconds continuously adjustable
	·Allow environmental humidity	100%HR
	·Signal output	4-20mA linear output two-wire system with HART communication protocol
		4-20mA square root output two-wire system with HART communication protocol
	·Start time	3S without preheating required
	·Vibration impact	2g 1000HZ ±0.05%
	·Impact resistance	50g 11mesc
	·Load characteristics	Corresponding to power supply voltage impedance of 50 Ω~1000 Ω (see figure)
	·Power supply	12V～36V DC
	·Sensor range ratio	20: 1. Continuously adjustable, zero point can be reversed and migrated 100%
	·Installation location impact	Non horizontal installation generates a zero point error of less than 0.25KPa, which can be corrected by adjusting the zero point,
		Does not affect measurement accuracy
	·Electrical connection	The cable sealing shell is suitable for cables with an outer diameter of 6-8mm;
	·Process Connection	1/4NPT internal thread; Connection of pressure conduit; M10 internal hole thread; Installation bracket connection
	·Contact with medium	Sensor corrugated membrane: stainless steel 316L, Hastelloy C;
	Partial materials	Sensor sealing ring: Fluorine rubber EPDM, PTFE carat (Kalrez);
		Flange: Stainless steel 316, Hastelloy C
	·Non contact with the medium	Shell: Die cast aluminum strip with epoxy resin coating; Fastener: Stainless steel
	Partial materials	Nameplate: Stainless steel 304; Intermediate fluid in sensor: silicone oil
	·On site terminal	Intelligent: 5-digit LCD digital display; Simulation: 3 1/2 digit LCD digital display
	·Explosion proof level	Explosion proof Ex d Ⅱ C T6 Gb; Intrinsically safe Ex ia Ⅱ C T6 Ga

---

---

Exterior structure

load characteristic

electrical connection

Instrument installation

On site mediation

Customers can adjust the horizontal viewing angle direction of the die cast aluminum shell by adjusting the fastening structure according to on-site installation requirements,

Make the instrument more convenient for on-site observation and installation (see the left figure above)

When selecting intelligent electronic components for instrument zero point and range adjustment (as shown in the figure on the right), they can be placed on the display

Adjust the buttons on the display.

communication function

Adopting intelligent electronic components with remote communication function. Customers can use the RX375HART communication handheld device or the Guancheng company's dedicated one

Communication module connected to PcTerminal, remotely adjust various parameters of the instrument at any location in the instrument measurement system, and monitor the operating status of the instrument.

The specific operation content includes: zero pointFull range adjustment, zero point no pressure automatic calibration, full range no pressure adjustment calibration, monitoring

Instrument pressure value, temperature value, output current value, maximumMinimum output value alarm, instrument wiring system fault diagnosis alarm, etc,

Provided customers with very convenient usage conditions.

On site terminal

The MSG6100 series pressure transmitter can be equipped with an optional LCD display. When using analog electronic components, it is necessary to select 3 1/2 LCD digital components

monitor.When using intelligent electronic components, a 5-digit LCD digital display should be selected.

The MSG6130 series differential pressure transmitter can make the following settings through the three buttons on the display: change LCD display, change

UnitMigration, setting zero and full degrees, setting damping zero point calibration, output signal standards, actual zero and full degrees, installing for customers

Request to migrate output.

Order Selection Table